Home / Services / Gates & security bars

Gates & security bars

Gate and security bar welding done at your property

A gate that will not latch or a burglar bar that has rusted loose is an open door. Our gate and security bar welding service repairs, rebuilds and fabricates the steel that secures homes, storefronts and yards, on-site and with protection against the humidity that caused most of the damage.

Close-up of a rusted metal gate

Quick answer

Gate and security bar welding means repairing or fabricating driveway gates, pedestrian gates, fence panels, burglar bars, window guards and security doors on location. A mobile welder rebuilds hinges, latches and rusted rails, re-hangs gates so they swing true, and fits quick-release hardware where bedroom windows need an emergency exit, then primes and paints the work.

Key points

Driveway, slide, swing and pedestrian gates repaired or built on-site

Burglar bars, window guards and security doors fixed, reinforced or fabricated

Quick-release hardware fitted on sleeping-room windows for safe emergency exit

Rusted bottom rails and post bases cut out and replaced, not covered up

Primer and finish coat applied before we leave to slow the next round of rust

What gate and security bar welding covers

Most calls fall into one of three situations. Something broke, such as a hinge knuckle snapping or a gate dragging after a car tapped it. Something rusted, usually a bottom rail, a post base or the lower anchor tabs on a set of burglar bars. Or something is missing, like a new pedestrian gate, a security door for a back entry or bars for a ground-floor window.

We handle steel tube, solid bar, ornamental iron and aluminum gates, swing and slide, manual and automatic. For automatic gates we weld and realign the frame, rollers, track and operator brackets; the operator electronics themselves are a job for a gate operator technician, and we are happy to coordinate with yours.

Why humid air and salt break gates and burglar bars

Security steel fails in predictable places. Water runs down the pickets and sits in the bottom rail, the rail rusts from the inside out, and one day the gate sags or a picket pulls free. Burglar bars anchored into brick or stucco trap moisture behind their mounting tabs, and the tabs thin until a firm pull would take them off the wall.

Near the coast, in places like the Houston Ship Channel corridor or the bayfront neighborhoods of Baytown, salt speeds all of this up. Gates in clay-soil cities also fight shifting posts, which put stress on hinges and welds every time the ground swells or shrinks. Our blog covers simple upkeep that slows these failures between repairs.

Hollow tube with no drain holes filling with water and rusting from inside

Hinge pins worn oval, letting the gate drop and drag on the drive

Posts leaning as soil moves, pulling latches out of alignment

Old welds that were never primed, now cracked along the rust line

Paint failing at the bottom of bars where sprinklers hit them daily

Brown metal fence near trees

Repair or replace: how we judge a damaged gate

A gate is worth repairing when the frame is mostly sound and the damage is concentrated: a broken hinge, one rotted rail, a bent corner. We cut out the bad section, splice in new tubing of the same gauge, weld it in and grind it smooth so the repair disappears under paint.

Replacement makes sense when rust has spread through most of the bottom rail and pickets, when the frame is badly racked from an impact, or when the design itself is the problem, such as an undersized frame on a long driveway gate. In those cases we quote a new gate built to fit the existing posts and operator when they are reusable, so the cost stays focused where it is needed.

Burglar bars and fire safety: what should a bedroom window have?

Fixed bars on a sleeping room window can trap people inside during a fire. Residential codes typically require bedroom windows to work as emergency escape openings, which means bars over them need a release that opens from inside without keys, tools or special knowledge. Requirements vary, so confirm with your local code official.

When we repair or build burglar bars, we ask which rooms the windows serve. For bedrooms we fit hinged bars with an interior quick-release latch and check that the release is reachable and works smoothly. We also look at existing fixed bars and point out any that cover a sleeping room, because retrofitting a release is usually a modest job that matters a great deal.

Hinges, latches and track: keeping a gate swinging true

Many gate complaints are really hardware complaints. A gate that scrapes the concrete, slams, or will not latch is often hanging on worn hinges welded slightly out of line. We replace weld-on barrel hinges, heavy-duty ball-bearing hinges or adjustable hinges as the gate weight calls for, then set them so the gate is plumb and the latch meets its keeper every time.

Slide gates get the same attention at the bottom: worn V-groove wheels, bent track, broken guide rollers and cracked receiver brackets. A gate that runs smoothly puts less strain on its operator and lasts longer, which is often the cheapest fix available.

How a gates & security bars job works with Houston Mobile Welding

01

Send photos and measurements

Show the whole gate or window plus close-ups of the failure, with rough widths and heights so we can bring the right tubing and hardware.

02

Get a written quote

We confirm scope, whether parts must be replaced, any egress hardware needed, the finish and an available visit time.

03

Repair on-site

The crew cuts out bad metal, welds in new steel, rehangs and adjusts the gate or bars, and tests latches and releases.

04

Prime, paint and walk through

Welds are cleaned, primed and coated, and we show you how releases and adjustments work before leaving.

How much does gate and security bar welding cost?

Price depends on what is broken and how much new steel goes in, not on a flat rate. A single hinge rebuild on an accessible swing gate is a short visit. Replacing a bottom rail, building a new security door or fabricating bars for several windows takes materials, shop-style layout work and more time on site.

The quote breaks out the factors so nothing is a surprise.

Gate size, weight and whether it is swing, slide or automatic

How much rust must be cut out and replaced with new tube or bar

Number of windows or doors and whether egress releases are needed

Mounting surface: brick, stucco, wood framing or steel posts

Finish: primer only, brushed paint, or a matched color coat

Getting your property ready for the visit

A little preparation keeps the visit short. Move vehicles out of the swing or slide path, unlock the gate and operator, and cut power to an automatic gate if you know how. Clear plants and stored items away from walls where bars will be welded or mounted, since spatter and sparks travel.

Tell us about pets, sprinkler lines and anything flammable stored nearby. If the work is part of a bigger plan, such as a new driveway or a trailer parking pad, mention it so the gate is built to suit. Customers outside Houston can check coverage on our service areas page.

Frequently asked questions

Can you fix my gate without taking it off its posts?

Usually, yes. Most hinge, latch and rail repairs are welded with the gate supported in place or lifted slightly on blocks. We remove a gate only when a post must be replaced or the frame needs to be squared on flat ground. Automatic gates are disconnected from the operator during work and reconnected and tested before we leave.

Do burglar bars need quick-release latches?

Bars over windows in sleeping rooms typically need a release that opens from inside without a key or tool, so occupants can escape in a fire. Rules vary by jurisdiction, so confirm with your local code official. We fit and adjust quick-release hardware on new bars and can retrofit releases onto many existing fixed bars.

Why does my gate keep sagging after it was welded before?

Repeat sagging usually means the cause was never fixed. Common culprits are a leaning post from shifting soil, hinges too light for the gate weight, a frame with no diagonal brace, or rust inside the bottom rail. We check the post, hinge size and frame before welding, so the repair addresses why the gate dropped, not just where it broke.

Can you weld new parts onto an old ornamental iron gate?

Yes. Older wrought and ornamental iron can be welded with the right prep, though very old pieces may be true wrought iron or cast parts that behave differently from mild steel. We test, clean to bright metal, and choose filler and technique to match. Replacement scrolls and pickets can be matched closely enough to disappear once painted.

How long does a gate repair take on-site?

A straightforward hinge or latch repair is often finished within a few hours, including priming. A bottom rail replacement, slide gate track rebuild or new security door may take most of a day, or two visits if paint needs to cure between coats. The written quote includes a realistic time window so you can plan around it.

Do you weld aluminum gates?

Yes. Aluminum gates and fence panels are TIG welded with filler matched to the alloy, since aluminum cannot be welded with the same wire used on steel. Thin aluminum pickets need careful heat control to avoid burn-through. If your gate is powder-coated, expect the area around the repair to need touch-up, which we can match closely.

Secure the gate or window today

Send photos of the damage and the property address through the quote form. You will get a written scope, price and visit time.

Get a Free Quote
Welder creating blue sparks during an on-site repair
Houston Mobile Welding logo

On-site welding repairs and fabrication anywhere in Houston.

Free written quote · No obligation · Reply within one business day

Houston Mobile Welding

Get a free quote

Tell us what you need built or repaired. We'll reply with a clear written quote.